YAMAHA XS650 DIRT TRACK

DIRT TRACK

YAMAHA XS650 DIRT TRACK

Omar's dirt track fenders, tanks and other parts are popular with vintage dirt track racers. Our literature says our non-DOT approved tanks are for racing and off-road use only but some customers have ignored this warning and have converted their street bikes to a dirt track look. Fenders (tail pieces with seat cushion) are made of thicker fiberglass to resist crashes. Omar's tanks are also stronger and are made with VRS™ Isothalic resin which resists the resin-dissolving effect of oxygenated (alcohol) fuels. Even though 'resistant', we recommend gasohol not be used in any fiberglass tank. All fiberglass tanks and fenders come to you with an unpainted white gelcoat surface. Fiberglass tanks are not DOT approved for highway use.

Tank specs

Height 8-3/4" with cap

Width max 7-3/4"

Width rear 5-1/2"

Length 18"

Tunnel width 2-3/8"

Mount length, rear hole to leading edge over frame 15-1/2"

Weight 2-3/4 pounds

 

DIRT TRACK GAS TANK

1 gallon. Fits narrow frame bikes. Through-tank and tab mount. New tank mounted pet cocks. Go the Dirt Track Fender section to see our new Champion fender, that is unlike any Champion fender ever made! 

DIRT TRACK GAS TANK

Newly redesigned tank, (not shown in photo) has Champion-like collar around filler neck. 1 1/4 gallons. Fits narrow to 3" wide oil-in-frame bikes like Yamaha 500s. Through-tank and tab mount. Tank mounted pet cocks. Go the Dirt Track Fender section to see our new Champion fender, that is unlike any Champion fender ever made! 

Tank specs

Height 7-1/2" with cap

Width max 9-7/8"

Width rear 9-7/8"

Length 18-1/2"

Tunnel width 3-1/2"

Mount length, rear hole to leading edge over frame 14-1/2"

Weight 3 pounds

 

DIRT TRACK GAS TANK

Omar's largest volume Champion tank-about 1 1/2 gallons. Fits narrow frame bikes including a 650 Yamaha (if you remove the elephant ear cups). If using a small tank on a 650-order a narrow fender. This tank is made from a three-part mold and will show the mold lines-you may have to do a little body work before the normal prime/paint process. Tank mounts with front and rear tabs-my instructions will show different mounting techniques. Tank comes with non-rusting chrome filler neck (just like all our tanks), a gas cap with check valve and pet cocks. [Go the Dirt Track Fender section to see our new Long Champion fender, it is unlike any Champion fender ever made! If you have sat on a standard champion fender then you'll know why this fender is the only one to buy] 

 

Tank specs

Height 8" with cap

Width max 9-1/2"

Width rear 7"

Length 18-3/8"

Tunnel width 2"

Mount length, rear hole to leading edge over frame 16-3/4"

Weight 3 pounds

 

 

Tank specs:

Width of tank

In The Back 6"

In The Front 9-1/2"

Width @ 15" From the Back of Tank is 9-1/2"

Width of Tunnel; 2-1/2" in Back

Width of Tunnel; 3-1/2" in Front

Overall Length 20"

YAMAHA XS650 GAS TANK

1 1/4 gallons. Fits narrow frame bikes. Comes with center mount kit and racing style tank-mounted petcocks. This tank has been redesigned from above photo-the back has been smoothed over, the cap no longer sticks out at a slight angle and the center mount hole is covered with my trade-marked hidden center mount hole. 

Tank specs

Height 7-1/2" with cap

Width max 9-3/4"

Width rear 6"

Length 19-1/4"

Tunnel width 3-1/4"

Mount length, rear hole to leading edge over frame 16-1/16"

Weight 4 pounds

 

Omars Trackmaster #TMT  2 gallons

Fits narrow to 3" wide oil-in-frame bikes. Comes with center mount kit and racing style tank mounted petcocks. 

Height 7" with cap

Width max 9-5/8"

Width rear 5-5/8"

Length 19"

Tunnel width 3-3/8"

Mount length, rear hole to leading edge over frame 17-1/4"

Weight 3 pounds

 

YAMAHA XS650 GAS TANK

Here's a perfect tank for SR/TT/XT Yamahas, HD Sprints and whatever else you want it on. It's fairly spacious and has almost a 2 gallon capacity. It has a large channel and fits over frames that are up to 3" wide. Yes, you can get to the oil filler cap on 500 Yamahas. Omar's own styling based on the Harley XR. Center mount. Comes with a vented gas tank cap, tank mounted pet cocks and a center mount kit. Specs-18" long, 9.5" wide at widest point. 5.75" wide at rear and it's 6" tall.

Designed to fit behind a stock tank

The XRWS is for use with stock 650 tanks. This photo is the original gray covered pattern before finish sanding and polishing. The final fender will come in white gelcoat. The sides of the XRWS are smooth from front to back. There is a dropped pocket in the fender. The dropped pocket sits on the frame cross member. The front of the fender is secured by the rear tank mount post. Cushion foam is high quality and molded from single foam block, not scrap foam bits like others. It is covered with a heavy weight vinyl and has a textured Street Fighter top. We provide well nuts and bolts so mounting is limited to drilling two holes in the frame. Kit includes fender, cushion, mounting hardware and instructions. The XRWS fender is $285. If you want us to fiberglass in a removable taillight/license plate holder to the underside of the fender, the total price is $434. 

Fender specs;

Length - 27.75"

Width underside:

at front 6-1/2"

at 12" back 10"

at 20" back 9-1/2

Designed to fit behind our Street Tracker tank.

Over the years Omar's has sold hundreds of XRWO fenders. As you can see in the photo the sides on the XRWO fender are smooth from front to back. There is a dropped pocket in the fender. The dropped pocket sits on the frame cross member. We provide well nuts and bolts so mounting is limited to drilling two holes in the frame. The front of the fender is secured with the rear tank mount post. This fender is molded to kiss fit the back of our Street Tracker tank. Cushion foam is high quality and molded from single foam block, not scrap foam bits like others. It is covered with a heavy weight vinyl and has a textured Street Fighter top. Kit includes fender, cushion, mounting hardware and instructions. This XRWO fender is $285. If you want us to fiberglass in a removable taillight/license plate holder to the underside of the fender, the total price is $434. 

Fender specs;

Length - 27.5"

Width underside:

at front 5-1/2"

at 12" back 10-1/4"

at 21" back 10"

Fender specs

Width underside

At front - 5 1/4"

At 5" back - 7 1/2"

At 20" back - 10"

Length overall

26 1/2"

Sleek rounded style is designed for narrow frames with 5" wide frame rails behind tank. Use on 650 and 500 Yamahas with our Omar tank. Cushion foam is high quality and molded from single foam block, not scrap foam bits like others. It is covered with a heavy weight vinyl and has a textured Street Fighter top. We provide well nuts and bolts so mounting is limited to drilling two holes in the frame. Kit includes fender, cushion, mounting hardware and instructions. If you want us to fiberglass in a removable taillight/license plate holder to the underside of the fender, the total price is $409.

Fender specs

Width underside

At front 6 1/2"

At 5" back 8 1/4"

At 20" back - 10" Length overall - 27"